Ceiling White
Premium quality water-based vinyl paint with excellent opacity and minimal roller spatter.
ColorMaker CEILING WHITE is a premium super white water‐based flat paint formulated specifically for use on Interior ceilings, ColorMaker CEILING WHITE has been formulated as a long lasting finish, which has exceptional opacity along with an outstanding super flat finish.
Being lead‐free, ColorMaker CEILING WHITE is easy to apply and provides excellent hiding power with just one application when recoating, along with easy clean up in water. ColorMaker CEILING WHITE can also be tinted to most pastel shaded colours to enhance the look of your room. ColorMaker CEILING WHITE is available in 1lt, 2lt, 4lt, 10lt and 15lt pails to suit your every need.
ColorMaker CEILING WHITE is touch dry in 20 minutes and can be re‐coated in 2 hours, at 25 degrees with relative humidity. ColorMaker CEILING WHITE is designed specifically for Interior ceilings for nearly every room in the house. Due to its Ultra Flat Finish, it is ideal for the bedroom, study, lounge room and living areas, the dining room and the hallway.
ColorMaker CEILING WHITE should not be used for exterior applications or in rooms of high moisture i.e. bathroom, laundry (these rooms ceilings should be painted with ColorMaker SEMI‐GLOSS ACRYLIC) ColorMaker CEILING WHITE may only be used in kitchens that have an adequate exhaust system above the stove.
COVERAGE:
ColorMaker CEILING WHITE will cover 12 to 16 sq. metres per litre depending on the porosity and the texture of the surface.
SURFACE PREPARATION:
Generally, all surfaces must be clean, sound and dry. If mould is present, kill mould spoors with a bleach solution and rinse thoroughly. On unpainted interior surfaces, clean and dust down. Fill all holes and cracks with suitable interior filler then coat with 1‐2 coats of suitable undercoat/primer. On previously painted surfaces remove loose and flaking paint and wash down chalking areas. On areas where it is not possible to remove all these materials, apply ColorMaker OIL BASED SEALER BINDER and leave to dry for 48 Hours. All gloss surfaces should be completely dulled by sanding, then dusted and wiped clean with a damp cloth.
PLASTERBOARD, GYPROCK, FIBROUS CEMENT SHEETING –
New – Clean down surface free of dirt then dust down. On Fibrous Cement Sheeting leave nail heads flush with surface and coat ferrous nail heads with ColorMaker RUSTEND METAL PRIMER to avoid spot rusting. Fill all holes and cracks with suitable filler, let dry then sand and dust. Apply one coat ColorMaker ACRYLIC SEALER UNDERCOAT.
Old – Remove all loose and flaking paint, fill, sand and dust down. Spot prime bare and filled areas with ColorMaker ACRYLIC SEALER UNDERCOAT.
SET PLASTER, PLASTERGLASS –
New
–
Allow
surfaces
to
cure
and
dry
for
at
least
6
to
8
weeks
prior
to
painting.
Clean
down
thoroughly;
apply
one
coat
ColorMaker
OIL
BASED
SEALER.
Old
–
on
previously
painted
surfaces,
remove
all
loose
and
flaking
paint,
fill,
sand
and
clean
down.
Spot
prime
bare
areas
with
ColorMaker
OIL
BASED
SEALER.
BRICK, MASONARY –
New
–
Allow
surfaces
to
cure
and
dry
for
at
least
6
weeks
prior
to
painting.
Clean
down
thoroughly.
On
concrete
blocks
apply
one
coat
ColorMaker
ACRYLIC SEALER UNDERCOAT.
Old – on previously painted surfaces, remove all loose and flaking paint, fill, sand and clean down. Spot prime bare areas with ColorMaker ACRYLIC SEALER UNDERCOAT.
STIRRING:
Mix contents thoroughly prior to application. Use broad flat stirrer with a circular motion for best results.
THINNING:
Not usually required. However, in hot conditions or when painting very absorbent surfaces add no more than 10% water. When spraying up to 15% Water may be used to aid atomisation.
PRIMING:
Not normally necessary on previously painted acrylic surfaces. However, on new surfaces a primer or undercoat must always be used.
APPLICATION:
Apply one to two full even coats by brush, roller or spray over previously painted ceilings in relatively good condition. Alternatively, apply two full even coats by brush, roller or spray over newly prepared surfaces. Use a medium nap (12mm pile) roller on smooth and semi‐rough surfaces. Use a longer nap (20mm pile) roller on rough surfaces such as vermiculite. When spraying, use a 15 thou. Spray tip.
In hot weather, DO NOT paint in the afternoon, but rather wait until the next morning once the roof cavity has cooled. Dip brushes and rollers in water before use to keep them working freely, rinse them occasionally in clean water to keep them working efficiently. Avoid brushing over paint that has been drying for a few minutes, and allow any missed spots to dry before touching them up.
To prevent shadowing across your ceiling, always paint ceilings in the direction of the main light source
DRYING TIMES:
ColorMaker CEILING WHITE is touch‐dry in approximately 20 minutes, and can be recoated after 2 hours, under normal conditions (25 degrees with relative humidity).
Under cooler or humid conditions, allow longer drying times. Allow 72 hours after application, before subjecting coating to steam.
DO NOT apply ColorMaker CEILING WHITE in the heat of the day during summer, as this may affect adhesion and will cause an un‐natural accelerated drying of the product.
DO NOT paint when surface or air temperatures are above 35 degrees or below 10 degrees Celsius.
CLEAN‐UP:
Clean all painting equipment with water while still wet or with a suitable brush and roller cleaner when dry.
SAFETY
Provide adequate ventilation during use, particularly if using in enclosed areas. This material is NON‐TOXIC and NON‐FLAMMABLE. Clean spills immediately with absorbent material.
KEEP OUT OF REACH OF CHILDREN. NOT TO BE SWALLOWED.
GUARANTEE
ColorMaker products are tested under controlled laboratory conditions to ensure the highest standards. However, as the use of ColorMaker product is beyond the control of the manufacturer, liability is limited to the replacement of material only, if proved faulty. The manufacturer is not responsible for any consequential loss or damage arising from the use or incorrect usage of this product and offers no warranty, express or implied. If in doubt, comprehensive information about ColorMaker products including application methods and conditions, suitable substrate types, longevity etc. can be obtained by contacting ColorMaker prior to application.
Product specification sheet
Ceiling White product specification sheet opens in a new windowManufacturer
Colormaker Industries

